Tank Volume Calculator (2024)

Tank Schematic: Horizontal Cylinder
with flat tank heads

Tank Volume Calculator (1)

Calculator Use

Estimate the total capacity and filled volumes in gallons and liters of tanks such as oil tanks and water tanks. Assumes inside dimensions of the tank.

Enter U.S. dimensions in feet (ft) or inches (in), or metric dimensions in meters (m) or centimeters (cm). Results are presented in U.S. fluid gallons, Imperial (UK) gallons, cubic feet (ft³), metric liters and cubic meters (m³).

*Actual fill volumes may differ. Tank volume calculations are based on tank geometries shown below. These tank shapes are calculated assuming exact geometric solid shapes such as cylinders, circles and spheres. Actual water and oil tanks may not be perfect geometric shapes or might have other features not accounted for here so, these calculations should only be considered estimates.

Methods to calculate the volume of tanks and the volume of a liquid inside a tank

The methods below will give you cubic measures such as ft3 or m3 depending on your units of measure. If you're calculating filled tank volume by hand using these methods you can covert cubic feet to gallons, and cubic meters to liters using our Volume Conversion Calculator.

Horizontal Cylinder Tank

Tank Volume Calculator (2)

Total volume of a cylinder shaped tank is the area, A, of the circular end times the length, l. A = πr2 where r is the radius which is equal to 1/2 the diameter or d/2. Therefore:
V(tank) = πr2l


Calculate the filled volume ofa horizontal cylinder tank by first finding the area, A, of a circular segment and multiplying it by the length, l.

Tank Volume Calculator (3)

Area of the circular segment, the grey shaded area, is A = (1/2)r2(θ - sinθ) where θ = 2*arccos(m/r) and θ is in radians. Therefore, V(segment) = (1/2)r2(θ - sinθ)l. If the fill height f is less than 1/2 of d then we use the segment created from the filled height and V(fill) = V(segment). However, if the fill height f is greater than 1/2 of d then we use the segment that is created by the empty portion of the tank and subtract it from the total volume to get the filled volume; V(fill) = V(tank) - V(segment).

Vertical Cylinder Tank

Tank Volume Calculator (4)

Total volume of a cylinder shaped tank is the area, A, of the circular end times the height, h. A = πr2 where r is the radius which is equal to d/2. Therefore:
V(tank) = πr2h

The filled volume ofa vertical cylinder tank is just a shorter cylinder with the same radius, r, and diameter, d, but height is now the fill height or f. Therefore:
V(fill) = πr2f

Rectangle Tank

Tank Volume Calculator (5)

Total volume of a rectangular prism shaped tank is length times width times height. Therefore,
V(tank) =lwh

The filled volume ofa rectangular tank is just a shorter height with the same length and width. The new height is the fill height or f. Therefore:
V(fill) =lwf

Horizontal Oval Tank

Tank Volume Calculator (6)

Volume of an oval tank is calculated by finding the area, A, of the end, which is the shape of a stadium, and multiplying it by the length, l. A = πr2 + 2ra and it can be proven that r = h/2 and a = w - hwhere w>h must always be true. Therefore:
V(tank) = (πr2 + 2ra)l

Volume of fill of a horizontal oval tank is best calculated if we assume it is 2 halves of a cylinder separated by a rectangular tank. We then calculate fill volume of 1) a Horizontal Cylinder Tank where l = l, f = f, and diameter d = h, and 2) a Rectangle Tankwhere l = l, f = f, and rectangle width w is a = w - h of the oval tank.
V(fill) = V(fill-horizontal-cylinder) + V(fill-rectangle)

Vertical Oval Tank

Tank Volume Calculator (7)

To calculate volume of an oval tank find the area, A, of the end, which is the shape of a stadium, and multiply it by the length, l. A = πr2 + 2ra and it can be proven that r = w/2 and a = h - wwhere h>w must always be true. Therefore:
V(tank) = (πr2 + 2ra)l


To calculate fill volume of a vertical oval tank it is best if we assume it is 2 halves of a cylinder separated by a rectangular tank. With r = w/2 = height of the semicircle ends, we can define 3 general fill position areas.

  • Fill, f < r
    We calculate fill volume using the circular segment method, as in a Horizontal Cylinder Tank, for the filled portion.
  • Fill, f > r and f < (r+a)
    The filled volume is exactly 1/2 of the cylinder portion plus the volume of fill inside the rectangular portion.
  • Fill, f > (r+a) and f < h
    We calculate fill volume using the circular segment method, as in a Horizontal Cylinder Tank, for the empty portion. Volume will be V(tank) - V(segment).

Horizontal Capsule Tank

Tank Volume Calculator (8)

We treat a capsule as a sphere of diameter d split in half and separated by a cylinder of diameter d and height a. Where r = d/2.
V(sphere) = (4/3)πr3, and
V(cylinder) = πr2a, therefore
V(capsule) = πr2((4/3)r + a)

Tank Volume Calculator (9)

Volume of fill for a horizontal capsule is done by using the circular segment method for the Horizontal Cylinder and, with a similar approach, using calculations of a spherical cap for the sphere section of the tank where,
V(spherical cap) = (1/3)πh2(3R - h)

Vertical Capsule Tank

Tank Volume Calculator (10)

To calculate the volume of a vertical capsule tank treat the capsule as a sphere of diameter d split in half and separated by a cylinder of diameter d and height a. Where r = d/2.
V(capsule) = πr2((4/3)r + a)


To calculate fill volume of a vertical capsule calculate in a fashion similar to the method used for the Vertical Oval Tankwhere r = d/2 = height of each hemisphere end.

  • Fill, f < r
    We calculate fill volume using the spherical cap method, for the filled portion.
  • Fill, f > r and f < (r+a)
    The filled volume is exactly 1/2 of the sphere portion plus the volume of fill inside the vertical cylinder portion.
  • Fill, f > (r+a) and f < h
    We calculate fill volume using the spherical cap method for the empty portion. Volume will be V(tank) - V(spherical cap).

Horizontal 2:1 Elliptical

Tank Volume Calculator (11)

Horizontal 2:1 Elliptical with 2:1 semi elliptical tank heads

Horizontal Dish Ends

Tank Volume Calculator (12)

Horizontal Dish Ends with dish only tank heads

Tank Volume Calculator (2024)

References

Top Articles
Latest Posts
Recommended Articles
Article information

Author: Ouida Strosin DO

Last Updated:

Views: 6588

Rating: 4.6 / 5 (56 voted)

Reviews: 95% of readers found this page helpful

Author information

Name: Ouida Strosin DO

Birthday: 1995-04-27

Address: Suite 927 930 Kilback Radial, Candidaville, TN 87795

Phone: +8561498978366

Job: Legacy Manufacturing Specialist

Hobby: Singing, Mountain biking, Water sports, Water sports, Taxidermy, Polo, Pet

Introduction: My name is Ouida Strosin DO, I am a precious, combative, spotless, modern, spotless, beautiful, precious person who loves writing and wants to share my knowledge and understanding with you.